Mike Barkmin

Schrauben

Verlängerung für M8-Schrauben: Ein Zylinder mit durchgehendem M8-Innengewinde zum Aufschrauben, eine separate Gabel zum Aufstecken auf einen Balken und eine passende M8-Gewindestange ohne Kopf. Die Gabel nimmt die Biebelast vom Gewinde und wird liegend gedruckt, sodass die Schichten entlang der Arme laufen.

Vorschau
Parameter
include <BOSL2/std.scad> include <BOSL2/threading.scad> // Schraubenverlängerung: Zylinder mit durchgehendem M8-Innengewinde, // separate Gabel zum Aufstecken und passende M8-Gewindestange ohne Kopf Thread_D = 8; Pitch = 1.25; /* [Verlängerung] */ Length = 35; Wall_Thickness = 2.0; // Holes shrink in FDM, require more clearance Clearance_Female = 0.2; // Chamfer at z=0 to prevent elephant foot from blocking the thread Elephant_Foot_Comp = 1.0; /* [Gabel] */ // Two arms that grip the beam on both sides and take the bending load off the screw. // Printed lying on its side, so the layers run along the arms. Beam_Thickness = 14; Beam_Clearance = 0.4; Arm_Thickness = 4; Arm_Width = 20; Arm_Height = 20; Base_Thickness = 3; Rounding = 1.5; // Pocket in the bottom of the fork that the top of the cylinder slides into Pocket_Depth = 5; Pocket_Clearance = 0.3; // Clearance hole for the rod through the fork base Rod_Hole_D = 8.2; Cylinder_D = Thread_D + Wall_Thickness*2; Gap = Beam_Thickness + Beam_Clearance; Fork_Length = Gap + Arm_Thickness*2; Base_Height = Pocket_Depth + Base_Thickness; /* [Schraube] */ Screw_Length = 40; // Print the rod lying down: layers run along the rod, much stronger against bending Screw_Lying = true; // Flat cut on bottom and top of the lying rod, gives a flat face on the bed Screw_Flat = 1.0; // Clearance for male threads Clearance_Male = 0.05; $fn = 72; // U-shaped side profile with all corners rounded (outer) and filleted (inner) module fork_profile() { offset(r=Rounding) offset(delta=-Rounding) offset(r=-Rounding) offset(delta=Rounding) union() { translate([-Fork_Length/2, 0]) square([Fork_Length, Base_Height]); for (side = [-1, 1]) translate([side * (Gap + Arm_Thickness)/2 - Arm_Thickness/2, 0]) square([Arm_Thickness, Base_Height + Arm_Height]); } } // Modelled upright (arms up, pocket at the bottom). The profile is extruded along Y, // so when printed lying on the front face all rounded edges are vertical and the // holes are teardrops pointing to +Y, which prints without support. module fork() { difference() { rotate([90, 0, 0]) linear_extrude(Arm_Width, center=true) fork_profile(); // Flat-topped teardrop, keeps enough wall above the pocket translate([0, 0, Pocket_Depth/2 - 0.01]) rotate([-90, 0, 0]) teardrop(d=Cylinder_D + Pocket_Clearance, l=Pocket_Depth + 0.02, cap_h=(Cylinder_D + Pocket_Clearance)/2 + 1); translate([0, 0, Base_Height/2]) rotate([-90, 0, 0]) teardrop(d=Rod_Hole_D, l=Base_Height + 2); } } // Verlängerung difference() { cylinder(d=Cylinder_D, h=Length); translate([0, 0, Length/2]) threaded_rod(d=Thread_D + Clearance_Female, l=Length + 0.2, pitch=Pitch, internal=true, bevel=true); translate([0, 0, -0.01]) cylinder(d1=Thread_D + Elephant_Foot_Comp*2, d2=Thread_D, h=Elephant_Foot_Comp); } // Gabel, lying on its side translate([0, -Cylinder_D/2 - 5, Arm_Width/2]) rotate([90, 0, 0]) fork(); // Gewindestange Screw_D = Thread_D - Clearance_Male; if (Screw_Lying) { translate([0, Cylinder_D/2 + Screw_D/2 + 5, Screw_D/2 - Screw_Flat]) difference() { threaded_rod(d=Screw_D, l=Screw_Length, pitch=Pitch, bevel=true, orient=RIGHT); for (side = [-1, 1]) translate([0, 0, side * (Screw_D/2 - Screw_Flat)]) cuboid([Screw_Length + 2, Screw_D + 2, Screw_D], anchor=side > 0 ? BOTTOM : TOP); } } else { translate([Cylinder_D/2 + 10, 0, Screw_Length/2]) threaded_rod(d=Screw_D, l=Screw_Length, pitch=Pitch, bevel=true); }
Schrauben

Teilbare URL erstellen

Abschnitte auswählen